Electrochemical Oxidation / Commercial & Support
Commercial & Support
Covering the path from a promising engineering fit to a working system: pilot testing, design consultation, cost estimation, proof of results, deeper technical reading, and answers to common questions.
This section assumes EO has already cleared engineering-level review. If you have not worked through the Engineering & System Design cluster or the decision gate yet, start there first — this layer is about moving from a validated design toward a purchase decision.
DECISION GATE
Not sure if EO applies? Start with the decision gate before requesting a pilot or proposal.
Why This Section Exists
The Engineering & System Design cluster answers how an EO system should be built. This section answers what it takes to actually get one: what a pilot test involves, how a design consultation works, what it costs, and what proof exists that deployments perform as designed.
Every page here is built around a specific next action, not just information — request a pilot, book a consultation, get an estimate, read a case study, download a paper, or find an answer.
Six ways to move forward
Choose Your Next Step
Request a Pilot Test
Submit stream data and receive a bench or pilot test protocol scoped to your contaminant, concentration, and discharge target.
Custom System Design Consultation
Work directly with a process engineer to size electrode area, current density, and power supply for your commercial system.
EO System Cost Estimator
Get an indicative capital and operating cost range from your flow rate, contaminant load, and target removal.
Case Studies
Review documented bench and full-scale results across PFAS destruction, landfill leachate, and industrial pretreatment.
Technical Papers
Download methodology notes, byproduct data, and charge-density reference curves used in our bench protocols.
FAQ
Answers to what we're asked most about scope, timeline, NDAs, sample handling, and commercial terms.
Where to Start
Go straight to Custom System Design Consultation — you have what a design session needs to size a real system.
Start with Request a Pilot Test, or get a rough number first from the EO System Cost Estimator if budget is the open question.
Start with Case Studies and Technical Papers & Downloads to assess technical depth and proof of results before engaging further.
How a commercial engagement proceeds
Four Steps from Test Data to Commissioned System
#1
Pilot or bench test
Establishes removal performance, charge density, and energy consumption on your actual stream, not a surrogate.
#2
Design consultation
Bench results are translated into electrode area, current density, and power supply requirements for your flow rate.
#3
Cost estimate and proposal
A capital and operating cost range plus commercial terms, scoped against the design from step two.
#4
Deployment and commissioning
System is built to spec, commissioned on-site, and verified against the bench baseline before handover.
Who does the engineering
Our Engineering Team Reviews Every Step
Engineer-reviewed, not templated
Test protocols, design specifications, and cost estimates are reviewed by a process engineer with direct EO deployment experience, not generated from a standard vendor sizing sheet.
Built on measured data
Specifications trace back to your bench charge-density curve and byproduct profile. Where bench data doesn't support a claim, the report says so.
NDA available at every stage
Sample submission, design consultation, and cost estimation can each proceed under NDA. Site identity and compound identity can stay undisclosed throughout.
Before You Start
No. Most people enter through whichever page matches their current question — cost, proof, or a specific next step — not a fixed sequence.
Start with the decision gate linked at the top and bottom of every page in this section, find out if electrochemical oxidation wastewater treatment technology is right for your stream.
The cost estimator, initial design consultation, and browsing case studies and papers are free.
The engineering & system design contents explains how an electrochemical oxidation wastewater treatment system should be designed. This section is about the commercial path to actually getting one built, tested, and quoted.
Where does this take you next?
This specific hub assumes EO already cleared engineering review. If you are earlier or later in the decision, these are the right next stops.
Still evaluating engineering fit
Review the electrochemical reactor, scale-up, energy, and integration decisions before moving to a commercial step.
Ready for a pilot test
Submit your matrix details and get a fixed quote before any sample ships, all you need to do is request a pilot testing now.
Want to see proof first
Review real deployment outcomes, trial, bench, and pilot testing results before engaging further.
Talk to our team about your next step
Whether you need a pilot test, a design consultation, or just a cost ballpark, send us your details and we will point you to the right starting page.
Electrochemical Oxidation Wastewater Treatment — Commercial & Support Hub by Evoaeo engineering team © All rights reserved.